Bellmouths and Manifolds

The place to buy your classic bike Brembo and Dellorto parts on line

NEW Genuine Malossi PHF/PHB/PHBE with 48mm thread trumpets 50mm long including mesh , £38.00 each
Limited quantity. Recomended for Laverda triples where space is tight these have a smaller max Dia than my usual stock PHF bellmouths below.

52mm mounting holes with 28mm center hole for some single manifolds £9.95 each

Std Air filters for 860/Darmah and some Singles just in £16.35

48mm thread PHF PHB PHBE

PHF/PHB/PHBE with 48mm thread fitment light grey plastic bellmouth, long out of production a getting rare now. Used on Ducati 750 round case with wire mesh. These have alloy mesh. 60mm long £75.00 used condition..... out of stock

PHF/PHB/PHBE with 48mm thread light grey plastic bellmouth, long out of production a getting rare now. Used on Laverda SFC and Ducati 750 with mesh and attachment ring . 60mm long £42.00 each

NEW Dellorto PHF/PHB/PHBE with 48mm thread trumpets with mesh 60mm long, current version black plastic £16.00 each

NEW PHF fitment Turned aluminium Bell-mouths
These have a 48mm dia thread to suit PHF/PHB/PHBE carbs. Overall length including mesh is Long 85mm , Medium 60mm , Short 50mm manufactured in Germany these are £36.50 each Please order PHF long/medium/short

Original grey short bell mouths for Darmah running PHF carbs. £16.00 Pair

New PHF threaded sleeves to allow you to fit air filter hoses on GT/GTS and Darmah etc. £6.00 each

52mm thread PHM

PHM fitment light grey plastic bellmouth, long out of production a getting rare now. Used on Ducati 900SS. Early versions used a wire mesh These have alloy mesh as used on the 77 onwards models £90.00 each Please ask as stock continually changing.Out of stock

NEW Dellorto PHM 52mm thread trumpets £16.00 each

NEW PHM fitment turned aluminium Bell-mouths
These have a 52mm dia thread to suit PHM carbs. Overall length including mesh is

Long 90mm , Medium 60mm , Short 50mm
Quality newly manufactured in Germany these are £36.50 each Please order PHM long/medium/short

VHB

NEW VHB 27-30 fitment Turned aluminium Bell-mouths with mesh
Thread is 34mm x 1.25 and will fit some SS1 carbs as well
Overall length including mesh is 75mm with a trumpet length of 60mm excluding mesh. Quality newly manufactured in Germany these are £34.50 each

NEW VHB 27-30mm carburettors with internal 34mm x 1.25 thread & SS1 25 – 30mm. 55mm long
Made from one piece of aluminium. £26.00 each

VHB 20-26mm carburettors with intake thread size M32 x 1.25mm 65mm Long
Made from one piece of aluminium. £26.00 each

Others

I have a pair of these brand new #5901 Will fit Dellorto UB, PHBG and VHB 20-26mm carburettors with intake thread size M32 x 1.25mm 76mm Possable outside cylinders on rearly MV/4's ? £45.00. i also have some used ones slightly longer of unknown origin.

NEW UA for carbs up to UA19 with external (male ) threads
Made from one piece of aluminium. £26.00 each

Manifolds

900SS rear manifolds. Malossi new. These will take PHM40s with wide stud space heads 58mm. Convert your Darmah ! £78.00 each

900SS front manifolds. Malossi new. These will take PHM40s with wide stud space heads 58mm. Convert your Darmah ! £78.00 each

these Malossi kits do away with the rubber gasket altogether and will last forever without going brittle or cracking. At the moment these are only available for PHM 40s and not the PHF 32’s

If you are retaining your original manifolds you will need to file the lip thast retained the rubber seal, off. The washers in the kit will be too big for the original manifolds as well however these kits can be made to fit the original manifolds.

Genuine Malossi intake kits for Wide stud heads running PHM40’s 900SS/MHR/LateSD/S2
Complete kit replaces your rubber inlet gaskets with Alloy plates and replaceable O rings.

Ideally this kit should be used with the genuine Malossi manifolds below or you will need to file the lip from your originals that locates the original rubber seal. Price is £48.00 a set for 2 carbs.

PHM 58mm inlet gaskets/rubbers £9.95 each 39mm center hole

PHF 52mm inlet gaskets/rubbers £9.95 each 35mm center hole

52mm mounting holes with 32mm center hole for some single manifolds £9.95 each

Genuine Malossi parallel inlet rubber for Laverda triples. These are 43mm each side. £11.95 each Or £14.00 each with a pair of Stainless jubilee clips (£2.50 each)

PHF parallel inlet rubbers for PHF30-36 with cable guides £8.95 each

Laverda 750 manifold and gasket set with new o-rings. For clamp fit PHF carbs. £80.00 one set only

Guzi manifold kits please ask