The place to buy your classic bike Brembo and Dellorto parts on line

dp

dp

NEW Dellorto PHF gasket and seal kit These sets are the full set and will do Laverda beam operated as well as Ducati , Moto Guzzi, BMW cable operated PHF carbs £14.50 each (each kit does one carb.)

NEW Dellorto alloy banjo fuel inlets for PHF £7.95 each.

NEW Flip top choke levers for PHF carbs, replaces the cables. 8293 Long  £16.50 each

Carb clamp rings for PHF carbs. £14.00 Please note: Dellorto have discontinued these for PHF so I have to get old ones blasted and re plated hence price. For this reason please be aware stocks will fluctuate.

OUT of STOCK

Genuine Dellorto pilot jets M5 x .75 mm PHM/PHF/VHB etc available from stock HERE

Genuine Dellorto Main jets M6 x .75 mm PHM/PHF/VHB etc available from stock  HERE

PHF Emulsion tubes available in sizes

AB260/262/264/265/268/270/272/275/278   £9.95 New larger range

Choke pick up jet PHF available in sizes

7746- 40/45/50/55/60/65/70/80/85/90 £4.85

Main jet holders in 2 sizes

Short 8885 £6.95

Long 8552 £6.95

K series needles for PHF available in sizes

Please see needles page HERE

PHF Air screw short tip (2.5mm) £4.80

Part No. 7449, Total Length 33mm, Tip Length 2.5mm ,Parallel shaft length 17.4mm

PHF Air screw short tip 7449 kit (2.5mm) . £7.35

Part No. 7449, Total Length 33mm, Tip Length 2.5mm ,Parallel shaft length 17.4mm

Needle retaining clip £1.00

Fuel inlet banjo filter £2.00 each

PHF tick over screw, slide height stop. Kit £7.35

M6 Carb top cable adjuster long £4.85

M6 Carb top cable adjuster short £2.85

M6 Nut for carb top cable adjusters 40p

Fuel Banjo bolts M6 £1.10

Carb top bolts M5 £1.10

Genuine  PHF carb inlet clamp bolt £2.35

Genuine half round nut for carb inlet clamp bolts.

These are no longer available from Dellorto so when these are gone that's it  £2.50 each

These cable angle fittings for carb tops will fit PHF and others. They are available in 50 70 90 degree angles. £5.40

Plastic cover for slide height screw, fits round knurled type not hex hd £3.00 each

PHF white floats £15.00 each

PHF Plastic carb tops.£5.00 each. Please state which you requirte as PHF and PHM are different sizes

PHF/PHM float valves available in  sizes 200/250/300 (250 is stock for PHF 32) Dellorto price £21.76

my price£17.50 each

Parts diagram for Dellorto PHF carbs

Dellorto stickers available in widths  100mm 130mm 170mm 190mm  50p each

PHF 36 DS NEW save £60  1 only available at £140.00

PHF 30 DD NEW save £60  1 only available at £140.00

PHF 36 BD

Stripped cleaned and checked with new seals £115.00

Main: 152

Pilot: 65

Needle: K4

Slide: 70/2

Float bowl nut 14mm spanner size used on most PHF/M carbs £12.75 each

Float bowl nut 21mm spanner size used on later PHF/M carbs £12.75 each

Float bowl nut washer  14mm spanner size washer used on most PHF/M carbs £0.70p each

NEW Dellorto alloy banjo fuel double inlet for PHF £7.95 each.

New Jubilee style Stainless clips for rubber inlet pipes ( filter box to carb.) These are 50mm to 70mm fit these are narrow band to fit the rubbers properly !

£2.50 each

Throttle slide spring 0.7 KG Light  £5.95 each

Throttle slide spring 1.4KG  Medium £5.95 each

Throttle slide spring 1.77KG  Heavy  £5.95 each

Dellorto’s replacement for the half round manifold clamp nut £1.10 each

Float bowl O-Ring, £2.25 each

Float bowl nut washer  21mm spanner size washer used on most PHF/M carbs £0.70p each

PHF Air screw long tip motoguzzi type  (5mm) £4.80

PartNo. 11084

Total Length 29mm, Tip Length 4.9mm ,Parallel shaft length 13.8mm

Float bowl nut 17mm spanner size used on later PHF/M carbs  £12.75 each

This uses the saame fibre washer as the 14mm spanner size nut above.  

Original Black 10g floats. These are good used condition as no longer available from Dellorto. These are a much better float than the white plastic floats supplied new which have a habit of not floating.  £19.50 each Out of stock

Dellorto no longer manufacture PHF carburettas with clamp type manifold fittings as used on  the 860/900 GTS, Darmah Pantah, 900SS and MHR . The only option is to rebuild your old carbs or go for as set of refurbished carbs. I refurbish all my own carbs, I use all new parts including slides where necessary. Even early type slides ( see my explanation of early/late slides here) are no longer available but later type can be adapted. I also keep all the spare parts for PHF in stock if you want to do your own refurbishment.

Should you want  do your own refurb I strongly recommend you change your float valves, your accelerator pump diaphragms Needles and needle jets as a bare minimum. You will also need a full gasket and seal set. One per carb.

I buy PHF 30/32/36 clamp fit carbs

PHF airscrew kit Part No. 9908 £7.35

Total length 36mm  Length of tapered tip 5mm.  Length of parallel shaft 12mm

Rubber caps that will fit std PHF bellmouths without mesh These will  keep rain stones small fury animals out of your engine when its parked up if you run open bellmouths. Ideally to fit 60mm dia £12.00 each

Complete cable choke assembly to replace flip top chokes.  £15.75 each

Choke piston £3.99

Choke piston spring 0.80p

Choke mount casting £3.99

Vacuum take off, 3mm bore for PHF carbs . £3.20 each

Laverda Tick over adjuster knob £18.00

Laverda carb mounting plate £32.00

PHF / PMM carb tops to suit LeMans 1 and Laverda for example. New £16.25 each or used £9.00 each

Stainless steel screw for Laverda mounting plate £0.65p each

Stainless steel screw to hold slide lift arm to rod and to hold dome top on, comes with Stainless lock washer £0.65p

Short or long cable adjuster boots for  throttle and choke inlets on PHF/PHM/VHB carbs £1.00 each

5mm bore vacuum pipe and t pieces for Laverda  vacuum take offs on PHF  Pipe £1.50 for 18”, t piece £1.00 each

PHF36 DD1/DS1  Brand New for LeMans 3

Motto Guzzi rubber mount PHF 36 DS/DD. These are brand new Dellorto’s. Dellorto no longer supply these carbs in natural alloy finish or with side pull tops. I have taken a new set of carbs, stripped them down and restored the original alloy finish then rebuilt these with refurbished side pull tops so basically these are brand new. Currently set as Dellorto supply these now for 850 guzzi’s they have

Main:130  Pilot:50  Needle:K18  Slide:60/3  Emulsion:265AB  Choke:70

This is what I start with                                       And this is the finished result

These are £725.00 and are supplied with the correct original grey bellmouths and can be jetted to suit your requirements at no extra charge.

Replacement CNC machined one piece alloy choke lever.

These will replace the plastic levers that are prone to snapping with age for example on the Ducati Darmah choke lever assembly mounted on the clocks

Also the flip top chokes mounted direct on some VHB,PHF,PHM carbs.

Not cheap but nicely made and should last a lifetime. £19.75 each

Laverda slide lift cables, cable length between nipples 66mm. Overall length 73mm £5.70 each

Metal cap for retaining the felt seal on  beam type tops used on Laverda and Guzzi. £1.25 each

PHF Cable op Slide lift arm  £14.00 each

Dellorto PHF carbs and Spare parts

Dellorto PHF 32 AD/AS

Fully rebuild set of 32’s with new slides, jets, atomisers,needles, pumps, float valves, banjo filters, cable adjusters, choke assemblies, gaskets and seal, new screws and  ultrasonically cleaned bodies. 860/Darmah setting but can be  set up to your spec. £545.00 pair

Main:     122
Pilot:     60
Needle:  K6
Slide:     70/1
Emulsion: 265AB

Accelerator pump nozzles for PHM available in sizes

7851-40/55/38/50/35 £6.25

Accelerator pump nozzle holder PHM  7470 £4.25

Accelerator pump pick up jet/valve for PHM

Part No.8557  £8.20

Pump adjuster stop and nut £4.65 pair

Accelerator pump diaphragm  Dellorto price £21.76

My Price £17.50  Temp unavailable

Accelerator pump diaphragm pump spring £1.55 each

Diaphragm pump housing screw and washer in stainless £0.70p each  3 needed

Pump housing bare casting £24.00 each new. £15.00 each good used

Dellorto accelerator pump parts

Pump top casting non return valve £16.00 each (Sorry even that's cheaper than Dellortos price)

Pump diaphragm gasket £3.45

Pump adjuster o-ring £0.70

Pump top casting valve o-ring £0.70

Pump nozzle o-ring £0.70

Pump nozzle holder fibre washer £0.45

Laverda  Triple  PHF top casting. Bare casting with bushes right hand side £28.00

Laverda  Triple  PHF top casting. Bare casting with bushes  Centre position £34.00

Laverda  Triple  PHF top casting. Bare casting with bushes left hand side  £28.00

Laverda triple top casting complete with shaft, cable lifter and end fittings. Right hand side £56.00

Laverda triple top casting complete with shaft, cable lifter and end fittings. Left hand side £56.00

Laverda triple top casting complete with shaft, cable lifter and end fittings. Centre position £64.00

Accelerator pump Arm for PHM 38/40/41 £4.80

Accelerator pump pin with spline for PHM Metal tops £2.30

Accelerator pump pin without spline for PHM plastic tops £2.30

Accelerator pump arm spring for PHM £0.80

Dellorto PHF 32 Laverda

This is a fully rebuilt set of 32’s for a Laverda triple. Probably about as near to new as you will find including New Jets, Emulsion tubes, needles, diaphragms, float valves, Air screws all gaskets and seals as well as new slides (these are £200 a set alone). Re-plated brackets and fixings. £765.00

Currently set up for a 3CL with

Needle: K1
Emulsion tube: 265AB
Main: 120
Pilot: 55
Slides: 60/2